Steps Necessary To Pass The 500-920 Exam from Training Expert TestkingPDF
Valid Way To Pass Cisco Channel Partner Data Center's 500-920 Exam
NEW QUESTION 25
The command show interface veth 705 is telling you that the bound interface is Ethernet 3/1/2 What is the location of the blade that has veth 705 associated to it?
- A. There is not enough information
- B. Chassis 1. Slot 2
- C. Chassis 3. Slot 2
- D. Chassis 3, Slot 1
Answer: D
NEW QUESTION 26
What occurs that causes a Split Brain Issue with Fabric Interconnects?
- A. A quorum tie occurs that must be resolved by the SEEPROM
- B. The subordinate Fabric Interconnect detects heartbeat failure and declares itself primary
- C. Manage configuration changes made with UCS Manager
- D. Both cluster links fail
Answer: B
NEW QUESTION 27
When troubleshooting UCS initialization issues that require Fabric Interconnect reboots, which Fabric Interconnect should be rebooted first?
- A. The subordinate Fabric Interconnect
- B. The Cisco UCS Manager will determine with Fabric Interconnect to reboot
- C. The primary Fabric Interconnect
- D. Both Fabric Interconnects must be rebooted simultaneously
Answer: C
NEW QUESTION 28
When troubleshooting, which option is the primary uses of the SCOPE command?
- A. To access the log files that reside in a component
- B. To access the log files on the virtual machines
- C. To access the log files on the log server
- D. The SCOPE command is not helpful in this case
Answer: A
NEW QUESTION 29
In Cisco UCS, there are several interfaces involved on the packet path from the vNIC through the adapter, IOM to finally reach Pi Which is the order of those interfaces, starting from the vNIC?
- A. HIF. SIF, VIF, UIF NIF
- B. VIF, UIF, HIF, NIF SIF
- C. HIF. NIF, UIF, VIF SIF
- D. VIF, UIF, HIF, SIR NIF
Answer: D
NEW QUESTION 30
The UCS Chassis Discovery Policy has been set to four and a new chassis is connected with two links What is the resulting chassis recognition action?
- A. The chassis will be recognized and both links will be active
- B. The chassis will be recognized but only one of the links will be active.
- C. The Chassis Discovery Policy will automatically reset to two links, since it always tracks the physical connections
- D. The chassis will not be recognized
Answer: D
NEW QUESTION 31
Which statement is true regarding the UCS Manager GUI is showing "Overall Status Unassociated" in the General tab for a C-series server?
- A. The server does not have a service profile assigned, but has been discovered by UCS Manager
- B. The server has a service profile assigned, but has connectivity issues with UCS Manager
- C. The server is not properly connected
- D. The server has been properly connected, but has not been discovered by UCS Manager
Answer: C
NEW QUESTION 32
A Hard Drive (HDD) has been hot swapped in a UCS server blade, however, the UCS Manager GUI is not displaying updated metrics about the replacement drive. What action will be required to properly display updated metrics?
- A. Remove and re-insert the server blade HDD controller mezzanine card
- B. Use the CLI, since HDD metrics cannot be displayed with the UCS Manager GUI
- C. Reboot the server.
- D. Reboot the Fabric Interconnects
Answer: A
NEW QUESTION 33
You are in the process of upgrading your UCS M3 Server to a newer UCS M4 Server. You associate the Service Profile to the new UCS Server, but it fails to boot You suspect of a failed boot hard drive. You check your RAID1 Boot LUN in UCS Manager, but see no error messages What could be causing the issue?
- A. A misconfiguration on the Service Profile Local Disk Policy
- B. A misconfiguration on the Service Profile Local Boot Policy
- C. The newer Cisco UCS M4 Server is using flash drives, not hard drives
- D. The newer Cisco UCS M4 Server is using disks of larger capacity than the previous UCS M3 Server
Answer: C
NEW QUESTION 34
A new UCS dual fabric cluster is being configured with a single chassis. The administrator notices that the cluster is not in High Availability (HA) mode. What is the possible cause?
- A. The HA plugin has not been installed in UCS Manager
- B. The UCS-FI-HA license has not been activated in UCS Manager
- C. The links to the chassis are not enabled
- D. No uplinks are active into the data center.
Answer: A
NEW QUESTION 35
Which ethernet port type is used when configuring UCS Fabric Interconnect connections to Cisco UCS C-series servers?
- A. Direct Connect Port
- B. Service Profile Port
- C. Server Port
- D. Uplink Port
Answer: D
NEW QUESTION 36
Which two interfaces allow access to Cisco UCS Manager? (Choose two )
- A. Cisco IMC
- B. Cisco UCS Manager GUI
- C. Cisco UCS Manager XML API
- D. Cisco KVM
Answer: B,C
NEW QUESTION 37
What three options should be verified, when you are able to connect to Cisco UCS Manager, but unable to open a KVM session to a blade? (Choose three)
- A. Verify the KVM IP Address is on the same subnet as the Fabric Interconnect management address
- B. Confirm the IP Address assigned to the KVM is not a duplicate IP
- C. Confirm the KVM IP Address is added to the route table in Cisco UCS Manager
- D. Confirm the IP Address assigned to UCS Manager is the same as the KVM address
- E. Verify TCP port 2068 is not blocked by an ACL or Firewall
- F. Verify the KVM IP Address is on the same ip subnet as the virtual machines
Answer: B,C,E
NEW QUESTION 38
Which are two benefits of integrating Cisco UCS C-series servers with Cisco UCS Manager? (Choose two ) Cisco UCS Manager provides the ability to automatically update C-series firmware and device drivers from a single global interface.
- A. Cisco UCS Manager uses service profiles and resource pools to allow the deployment of multiple servers with a single common template
- B. Cisco UCS Manager is able to act as a common centralized management platform for both blade and rack servers in a single domain.
- C. Cisco UCS Manager provides the ability to manage C-series in multiple physical domains from a single global interface
- D. Cisco UCS Manager can automatically power on and off servers to scale elastically according to application performance demands
Answer: B
NEW QUESTION 39
When troubleshooting a LAN connectivity issue, you notice a failed uplink from the Cisco UCS Fabric Interconnects to the upstream LAN switch. What two could be causing the issue? (Choose two )
- A. Misconfigured QoS parameters on the failed uplink
- B. A port channel mismatch between the Fabric Interconnects and the upstream LAN switch
- C. A SFP Type mismatch between the Fabric Interconnects and the upstream LAN switch
- D. A port speed configuration mismatch between the Fabric Interconnects and the upstream LAN switch
- E. Misconfigured VLAN on the failed uplink
Answer: A,B
NEW QUESTION 40
You are experiencing intermittent connectivity issues on one specific Cisco UCS server Some applications work, while other do not transfer data You suspect jumbo frames limitations Which two places do you check the jumbo frame settings? (Choose two )
- A. Check the fibre channel port configuration for jumbo frame configuration
- B. Check server's individual vNICs and/or vHBAs properties
- C. Check server's QoS System Class
- D. Check server's service profile and/or service profile template
- E. Check upstream switch ports frame size configuration
Answer: C,E
NEW QUESTION 41
......
All 500-920 Dumps and Cisco Data Center Unified Computing Infrastructure Troubleshooting Training Courses: https://www.testkingpdf.com/500-920-testking-pdf-torrent.html
